Microsemi Introduces New SAS/SATA HBAs And RAID Cards

gearbest.com

microsemi_adaptec_hba_1100_family

Microsemi Introduces New SAS/SATA HBAs And RAID Cards

 Today Microsemi is announcing the availability of a new generation of SAS/SATA adapters and RAID cards under their Adaptec brand. The new cards are based on the 28nm SmartIOC and SmartROC controller chips that Microsemi announced in May of this year. Those controller ICs are available for third parties to build products around, but Microsemi is now also selling their

own branded solutions. The new adapters and RAID cards all use a PCIe 3 x8 host interface and support between 4 and 24 SAS/SATA ports.

Microsemi Introduces New SAS/SATA HBAs And RAID Cards

The Microsemi Adaptec HBA 1100 family is the entry-level tier implementing basic host bus adapter functionality using the SmartIOC 2100 controller. Microsemi claims aggregate performance can reach up to 6.6 GB/s sequential and 1.7M 4kB IOPS, a substantial improvement over the 1.3M IOPS from the previous-generation HBA 1000 series. (1100 series HBAs with 8 ports or fewer are rated for only 1.5M IOPS.) With the switch from a 40nm controller fabrication process to 28nm, Microsemi also claims these are the lowest-power 12Gb/s SAS adapters on the market. All the expected features of a SAS controller are present, including support for enclosure management, multi-initiator support for high-availability clustering, and support for port multipliers allowing up to 238 drives to be connected to each HBA. Microsemi has added support for the command set extensions used by host-aware and host-managed Shingled Magnetic Recording (SMR) hard drives.

Microsemi Introduces New SAS/SATA HBAs And RAID Cards

gearbest.com

The Microsemi Adaptec SmartHBA 2100 family expands upon the features of the HBA 1100 family by enabling basic hardware RAID functionality, including RAID 0,1,10 and 5 modes. RAID arrays can span up to 32 drives, and drives not configured in a RAID array can continue to be accessed individually.

Microsemi Introduces New SAS/SATA HBAs And RAID Cards

The Microsemi Adaptec SmartRAID 3100 family includes all the features of the 1100 and 2100 families, including compatibility with the RAID metadata format of the 2100 series. The 3100 series adds DDR4 caches ranging from 1GB to 4GB, with optional power loss protection support on most models through the addition of an external capacitor module to power the card long enough to save the contents of its DRAM to the card’s flash memory. With the availability of a DRAM cache, the 3100 series can offer higher RAID 5 performance than the 2100 series plus support for more advanced RAID modes including RAID 6, 50 and 60. Models with power loss protection also support Microsemi’s maxCache SSD caching feature, allowing up to 1TB of SSD cache in front of hard drive arrays, with write-through and write-back caching modes supported and mirroring supported for the cache drives. Microsemi claims a 40% power reduction compared to their older Series 8 12Gb/s RAID adapters.

Most models of the new generation of Microsemi HBAs and RAID controller cards are available now. Models with a mix of internal and external ports, and models with 16 external SAS ports will be available in early 2018. Pricing has not been annnounced.

Microsemi Introduces New SAS/SATA HBAs And RAID Cards

Next year, Microsemi plans to add models supporting controller-based drive encryption, offering an alternative to the use of self-encrypting drives or host-based software managed encryption.

Source: https://anandtech.com

extra.com.br
Facebooktwittergoogle_plusredditpinterestlinkedinmail

6 thoughts on “Microsemi Introduces New SAS/SATA HBAs And RAID Cards

  1. Same thing happens to the ACPI command set in RAID. It’s hard to pass commands through to individual nodes in a logical disk when the command sets (NVMe included) are built around logical disks. NVMe RAID is no different…you loose a lot of power saving features when running them in RAID, at least in the LSi controllers I’ve dealt with that effectively multiplex the drives together, leaving them up to their own firmware when it comes to management.

  2. They support a weird passthrough mode of NVMe commands, but it's not really hardware RAID.

  3. My comment ain't really about HDD vs SSD actually. Plenty of SAS and SATA SSDs. And plenty of RAID controllers for those.

  4. The world will always need spinning disks to provide cheap storage.But these are really for storage servers.

  5. Not sure the world needs more SAS/SATA RAID controllers. What is sorely needed though are nvme RAID controllers. ESXi certified while we are at it.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>